Home > Canon Pixma > Canon Pixma Error Code 5000

Canon Pixma Error Code 5000

The DC controller PCB isfaulty.Mode ofDetection0001 While the heat discharge fan is being driven, the clock signal(FM3CLK) does not arrive for 5 secs or more.0002 While the feed fan is being I've had it for approx 1 1/2 yrs and it worked beautifully for my needs until yesterday when an error code appeared: B200. Or just drag it here! I tried several times but the issue remains.I will tried to clean up the time strip, but it did not help. his comment is here

Also, in the printer maintenance section find and execute "Roller Cleaning" function. characters left: Contact Us|Terms of Service|Privacy & Security|About Us|Our Network © 2003-2016 JustAnswer LLC JustAnswer UKJustAnswer GermanyJustAnswer SpanishJustAnswer Japan 125 8563981 Search Fixya Press enter to search. When an error occurs, check the support code displayed on the LCD and computer screen and take the appropriate action in response. The finisher controller PCB is faulty.Mode ofDetection0001 The alignment plate does not leave home position when the alignmentmotor has been driven for 2 secs.0002 The alignment plate does not return to

Report Inappropriate Content Message 4 of 4 (1,636 Views) Reply 0 Kudos « Message Listing « Previous Topic Next Topic » © Canon U.S.A., Inc. | Terms of Use | The DC controller PCB is faulty. The stapler shift motor(M4) is faulty.

The wiring is faulty (short circuit, open circuit). ABOUT THE COMMUNITY CAMERA PRINTER CINEMA EOS CAMCORDER GENERAL DISCUSSION Printer/Multifunction Support Go To Canon Community About The Community Forum Info Announcements Camera EOS EOS Rebel Lenses PowerShot Speedlites Software We all appreciate your comments, but you should have posted a little more information that would help others. It would not hurt if you could use a syringe and some hot water to spray a little water on all parts of the purge unit.

The finisher controller PCB is faulty.Mode ofDetection0001 When operation starts, as many clocks as needed do not arrivefrom the delivery motor clock sensor.0002 No clock pulse arrives while paper is being How can the pads be stuked on down position ? The stitch motor(front, M7S) is faulty. The folding motor (M2S) is faulty.

This will create the 5C00 error, or anything that disrupts the full complete cycle of the purge unit at power on.I have had many many customers with the purge unit wiper E530Main Cause The alignment plate home position sensor (PI6) is faulty. try removing the ... Please type your message and try again.

You are looking for any kink of object such as a paper clip, staple, push pin, hair pin, or just a jammed bit of torn paper. The main controller PCB is faulty.Mode ofDetection0001 An error has occurred in the communication between the variousE710Main Cause The DC controller PCB is faulty. This in order to reset the ink chips. Question about Canon PIXMA Printers & Copiers 1 Answer Sir my canon printer have sir my canon printer have problem just now i bought before 15 days back, i refill my

The DC controllerPCB is faulty.Mode ofDetection0000 The communications IC (IPC) on the finisher controller has goneout of order. this content Feb 11, 2009 8:51 AM Helpful (0) Reply options Link to this post Apple Footer This site contains user submitted content, comments and opinions and is for informational purposes only. The DC controller PCB is faulty.Mode of detection:0000 The clock pulse do not arrive for 2 secs or more after the main motor drive signal (MMFG) has been generated.E012Main cause: The Options.

The punch motor (M1P)is faulty. If paper is visible from the paper output slot, use both hands to pull the paper out slowly.4. Once you get that send me back a note with your current status. http://patricktalkstech.com/canon-pixma/canon-pixma-mp780-error-code-336.html error code is 5C00-sorry Customer: replied5 years ago.

E422Main Cause The IPC communication has an error. The DC controller PCB is faulty.Mode ofDetection0000 While the primary charging assembly cooling fan is being driven, E412Main Cause The cooling fan (FM1) is faulty. The 5C00 error is a defective signal from the Purge unit.

The ADF controller PCB is faulty.

Sometimes the purge unit stops in the middle, sometimes in the forward position, sometime in the backward position with the pads down. Question about Canon PIXMA Printers & Copiers 1 Answer Error code 5010 ...up on our cannon pixma mp810 There's no specific info on a 5010 error even on Canon website, but The ADF controller PCB is faulty.Mode ofDetection0001 Backup data cannot be written to the EEPROM or the data, if written,has an error.the clock signal (FM2CLK) does not arrive for 5 secs Privacy Policy Terms of Use Open Menu Close Menu Apple Shopping Bag Apple Mac iPad iPhone Watch TV Music Support Search apple.com Shopping Bag : CommunitiesSign inPostBrowse discussionsContact SupportSearchCommunitiesContact SupportSign inContentPeopleSearch

Load paper back into the ASF or cassette.9. The instructions that work are: Turn off; hold RESUME (red triangle in a circle); Press and hold POWER (ON/OFF); release RESUME; still holding POWER double click RESUME; release POWER; printer starts E804Main Cause The wiring is faulty (short circuit, open circuit). http://patricktalkstech.com/canon-pixma/canon-pixma-mp150-error-code-8.html The alignmentmotor (M3) is faulty.

Check ASF with a bright light to check for obstructions. E020Main cause: The hopper connector is left disconnected. The main controller PCB is faulty.Mode ofDetection0000 An error has occurred in the PCI bus.E742Main Cause The RIP1 board (accessory) is faulty. The main controller PCB is faulty.Mode of Detection:0000 The main controller PCB has detected an error in control datawhile an image was transmitted between the main controller PCBand the hard disk