Home > Error Code > Canon Fax Error Code List

Canon Fax Error Code List

Contents

to '1', CS fails to go '1'). •... Cause 3 The image data for the document to send was not found in memory when performing delayed sending or redialing. Cause: The other party experienced an echo malfunction. Manual of the model in question. ##322 [ RX ] Fixing assembly of the printer (LBP) is faulty... navigate here

Solution: Add a long pause after the telephone number when registering the user in the auto- dialing directory so that the system will not respond to the first DIS from the Page 98 Chapter 2: Service Error Codes ##244 [ TX/RX ] The unit used to control OPT2 malfunctioned Cause Remedy • The operation of the IC used to control • Replace You can check the error code on the Details screen when you press [Log] on the Status Monitor/Cancel screen. (See "Status Monitor/Cancel.") If a send, receive, or fax job does not Solution: Add a long pause after the telephone number when registering the user in the auto- dialing directory so that the system will not respond to the first DIS from the

Canon Fax Error Codes

Solution: Adjust the NL equalizer to receive picture signals properly. ************** ##670 [TX] At V.8 late start, the called party declares the V.8 protocol in DIS signal and this Page 42 Chapter1: User Error Codes #057 [ RX ] Recording paper feed fault Cause Remedy • The recording paper has jammed while the • Remove the jammed recording paper from Resend the fax after a while. C.

Page 187 [ TX/RX ] During an ECM mode procedure, a signal other than a significant signal was received Cause Remedy • The procedure signal is faulty. • Record the protocol Remedy 1 Check the settings for the WebDAV server. crease the transmission level so that GI2 may be received correctly. Canon Result Ng Solution: Take echo counter-measures as described in Service manual.

Remedy Delete unnecessary files from the memory media, file server, or Advanced Box, or create a new folder and move existing files to that folder to create room in the root A. Solution: Add an EPT to the V29 modem signals Solution: Adjust the continuous transmission time of 1 before transmitting the picture signal so the other party can receive picture signals Remedy Check the settings, and ask the sender to resend the data. #821 Cause You have received data that cannot be processed (TIFF analysis error).

Remedy Check the settings, and ask the sender to resend the data. #820 Cause You have received data that cannot be processed (BASE 64 or uuencode is incorrect). Canon Fax Machine Error Codes Cause: The other party cannot receive CFR2 due to poor line conditions. Cause 2 Verification of the SSL server certificate was attempted when sending with WebDAV because [Confirm SSL Certificate for WebDAV TX] is set to 'On', but verification failed and sending could Remedy Check the network connection to the cascade copy printer, and try again.

Canon Fax Error Code Ng

Cause: CPU malfunctioning due to noise. Solution: Have the other party boost the transmission level to receive the picture signals properly. Canon Fax Error Codes munications function (i.e., Canon mode • The other party does not support CD com- relay and confidential for G4); try a differ- bination in Canon mode. Canon Error #099 A.

Solution: Lower the transmission level so the echo of the CFR transmission is not received. ##104 [ TX ] RTN or PIN received during transmission. check over here Cause: The actuator malfunctions during cleaning. Solution: Adjust the NL equalizer to receive EOM from the other party properly. ##606 [ RX I Fail phase synchronization during MF1 reception. Page 83 Chapter 2: Service Error Codes ##122 [ TX ] ITU-T-compliant (DIS bits 33 through 37) transmission function is absent Cause Remedy • Bit 33 of DIS received from the Canon Error Code 801 Scan Folder

Increase the DTMF transmission level so that the sever may receive the DTMF signal correctly. Remedy Deliver the device information again after the destination client machine has finished executing its job. #850 Cause Device information could not be delivered because the destination client machine is operating Page 150 Chapter 2: Service Error Codes ##670 [ TX ] In V.8 late start, the V.8 ability was detected in DIS from the other party and, in response, CI was his comment is here Remedy 1 Wait a few moments, and then try again after the other send jobs are complete.

Page 144 Chapter 2: Service Error Codes ##603 [ TX ] In MF1 (Minifax 1) transmission, MCF cannot be received [Japanese model] Cause Remedy • The line condition is poor, and Canon Imagerunner Error Codes 099 Solution: Adjust the NL equalizer so the other party can receive the phase signal properly. ##007 [ TX ] Failed CFR2 reception during G2 transmission. Cause: Abnormal protocol.

Page 37 Chapter1: User Error Codes #046 [ RX ] Receiving restriction Cause Remedy • The telephone number of the other party • Register the telephone number of the other has

Remedy Contact your System Manager. #868 Cause Failed to communicate with the destination when sending with WebDAV, because access via a proxy server was requested (received HTTP Error 305: Use Proxy). Trademarks The product names and company names described in this manual are the registered trademarks of the indi- vidual companies. NL Equalizer: No.05 of Service Soft Switch #2 MENU Adjust the NL equalizer: Select 'ON'. 3. G3 Fax A.

Solution: Adjust the NL equalizer so the other party can receive picture signals properly. NOTE: This code is not in the G3 book even though several manuals indicates it is. ##675 [RX] ] The protocol did not move from phase 3 to phase 4 A. weblink JOB NO.

Remedy 2 Check the proxy settings. (See "Protocol Settings.") #869 Cause Received a response from the destination stating that authentication failed when sending with WebDAV (received HTTP Error 401: Unauthorized). Cause: The CS motor malfunctions. Adv. Solution: Refer to Service Manual. ##302 [ TX ] Interface error between reader and controller.

Page 167 MCF, PPR, or RNR was received after transmission of PPS-NULL Cause Remedy • The procedure signal is faulty. • Record the protocol on a DAT or MD, and have SUBADDRESS A subaddress is printed, if specified. Page 192 Chapter 2: Service Error Codes ##802 [ TX/RX ] Error occurred in the reception of a message from the hard disk Cause Remedy • The message from the hard However, if a send job is cancelled, "STOP" is printed in the Results column on the Send Report. (See the Getting Started.) Perform the necessary procedures according to the error code.

Cause: The transmitter disconnected the line during phase 3 or unable to detect the signal from the transmitter. Remedy 1 Scan the original and perform sending again. Solution: Boost the transmission level so that the other party can receive the signals immediately before GC2, PIS or the Phase signals.