Try this again and when you see the rocker arm go down, pull the power cord immediatley. Very important: Hold down the stop/cancel button. Why couldn't the service tech tell me this??????? by unknown on Feb 2, 2011 at 5:59pm Add comment Please sign in to comment 0 "Paper jam in the Document Feeder occured. http://patricktalkstech.com/error-code/canon-mp530-printer-6a00-error-message.html
Well worth having ink all over my fingers!!!! by unknown on Jun 3, 2013 at 7:22am Add comment Please sign in to comment 0 Truckman,... Let me opt out and see if someone else can help. Then I noticed a piece of torn paper lodged inside.
I've tried many of the suggestions recommended on this forum, including cleaning the print head and other areas that I can reach and/or remove, and making sure the purge cleaning station Working... Richard is online now My Canon pixma mp530 says 6a00 check printer Resolved Question: My Canon pixma mp530 says 6a00 check printer Submitted: 5 years ago. Error Code 6a00 Canon Pixma Ip6600d Any advice would be greatly appreciated.
How JustAnswer Works: Ask an Expert Experts are full of valuable knowledge and are ready to help with any question. I have had such great success with this printer that I would look for a newer model of this printer whenever I need to replace this one. IT IS NOT DESIGNED TO HAVE PAPER PULLED BACKWARDS WHILE IT IS TRYING TO FEED IT FORWARD. Now you can move the carriage by hand.
All the gray sponges seem to be in place, but it (MP800) wont feed paper from the top tray. Canon Mp530 Service Manual Locate the small screw on the then exposed top right front -- loosen it about one turn and everything was back in working order. Credentials confirmed by a Fortune 500 verification firm. i need to get a tack that was lodged in the middle of the printer.thanks!Nolan by nolany on Nov 9, 2007 at 2:56pm Add comment Please sign in to comment 0
The bad news is you also took out the wiper blade that normally sits on the top of the purge unit. May people imply that you can just open the cover and physically move the printhead carriage. Canon Printer Error Code 6a00 Oh, well, back to HP. Canon Mp610 Error 6a00 How much are your instruction manuals and how can I get my hands on one?Best regards,Daniel by unknown on Dec 19, 2008 at 8:41am Add comment Please sign in to comment
Again, it may take a few minutes for the printer to get itself realigned but should now work by unknown on Nov 17, 2007 at 3:06pm Add comment Please sign in http://patricktalkstech.com/error-code/canon-mp530-error-code-6a00.html Get a Professional Answer Via email, text message, or notification as you wait on our site.Ask follow up questions if you need to. 100% Satisfaction Guarantee Rate the answer you receive. by unknown on Apr 27, 2009 at 8:42pm Add comment Please sign in to comment 1 I moved the print carraige all the way to the left (power off)found and removed Hope this help by Anonymous on Mar 9, 2007 at 11:32pm Add comment Please sign in to comment This did the trick. Canon 6a00
that could be interferring with anything. Have a manual for Canon PIXMA MP530 All-In-One InkJet Printer? You will have to get the top covers off to get at it. his comment is here Did this answer your question?
The print head cartridge keeps locking itself up on the right hand side.2. Canon Purge Unit Repair I looked at the purge unit, and the wiper to the rear looks like it has been ripped off. I didn't have any black ink coming out of my MP530.
Was this perhaps the wiper mechanism, or at least part of it? Moral is make sure that white plastic wiper can seat all of the way. If so what do I do now?Thanks.Chatty - Chatty Kathy 0 Kathy,...Yes,..that is usually the typical way a problem occurs. Canon A6000 I was able to fix it by cleaning inside by the ink with a wet towel paper. - Simon Klein 0 Ive had problems with an MP780 but in UK under
They wanted me to send it for repair 2 hours away!!I've had better luck with HP printers malfunctioning after4-6 years of use!!! I moved the print heads back and forth a couple of times to make sure there was no more paper stuck, turned it off and on and yes ahhhh it works Took out all the ink cartridge, pushed the cartridge holder back and forth and cleaned the inside without taking it apart. weblink Thank you!! - Anonymous That's thrue.I could push the sponge back on his place and after restarting the error 6A00 was disappeared.Thanks - Anonymous It works!!!!!!
I googled the message number and got this page. Any help would be greatly appreciated...thank you by gbernier on May 20, 2010 at 8:25pm Add comment Please sign in to comment 0 gbenier,...You are correct, the MP530 is one of Look for paper shard or paper clip or staple or anything that doesn't belong and will cause trhe mechanism to stop moving.BABAuthorized Canon Tech by BAB on Aug 8, 2007 at By the way...the manual does not tell you how to take out the purge unit, you don't have to take out the NCU board, the NCU sub board, or the logic
I have sent each of you a response, but today I found out that the document I created to give you all the information you wanted and to show some simple It should take very little force and should be smooth all the way and you should not bump into anything. The lower rubber rollers on the carriage are about 3/8 wide and the uppers are about 5/16 wide. Use an eye dropper and put some windex on each pad.
In any case thank you for your help, I was about to buy a new printer and this one is only a year old and has had very little use. I even purchased the service manual and started taking the printer apart, but stopped when I had to start taking things off the motherboard. Up next TCT - How to remove and clean Canon Printhead - Duration: 5:30. I've tried most of the moves suggested here...cleaning the printhead, depressing the purge sponges etc.
Canon tech will give me the finger one through ten.. thetechtree 15,958 views 6:58 Enable canon MP530 - Duration: 2:46. no paper, sensor?noted the white roller are elevated slightly.we had a input jam caused by a broken paper input sensor, which was removed.we service out of warranty printers here in Canada. Now that the power is off, you can move the printhead asm to the far left and this will give you a little more room to access the purge unit.