Home > Error Code > Canon Super G3 Error Codes

Canon Super G3 Error Codes

Contents

Password A password used by a Canon facsimile machine may be any of the following: Polling Password: This is an ID number used for polling between Canon machines, and is also Cause: The other party cannot receive signals properly due to poor line conditions. Solution: Relax the RTN transmission conditions to prevent RTN transmission. Cause: The read end sensor stays ON or OFF. his comment is here

Solution: Have the other party boost the transmission level to receive ACK properly. ##735 [ RX ] Excessive REJ transmission (3 times) during retransmission procedures upon ARQ reception. Cause Remedy... A. celed the memory transmission reservation. • In the case of reception, the user deleted •...

Canon Fax Error Code Ng

Solution: Adjust the NL equalizer so the other party can receive picture or Q signals properly. Page 202 Chapter 2: Service Error Codes ##1021 [ TX/RX ] Call rejected Cause Remedy • Cause number #21 (Call rejected) arrived • Start a communication once again. Page 115 Chapter 2: Service Error Codes ##304 [ RX ] Memory copying cannot be used Cause Remedy • An internal unit is faulty (i.e., during • Correct it by referring

A. Manual of the model in question. ##303 [ TX/RX ] Page memory error Cause... Page 35 Chapter1: User Error Codes #042 [ RX ] Cutter operation is faulty Cause Remedy • The cutter used to cut thermal recording • Correct it by referring to the Canon Error #099 ManualsOnline product support member asks: System Error E225 for a canon fax machine Super G3 Fax Machine.

Increase the T5 timer setting to avoid an error. Canon Fax Machine Error Codes Page 98 Chapter 2: Service Error Codes ##244 [ TX/RX ] The unit used to control OPT2 malfunctioned Cause Remedy • The operation of the IC used to control • Replace functioned because of an echo. • Using a manual call, press the Start button after hearing the 1 st DIS from the other party. •To prevent response to the 1st DIS Cause: Cannot transmit signals properly due to poor line conditions.

When all documents have been read into memory, memory transmission reservation may be selected as in the case of memory transmission. 14. Fax Error Codes Ricoh Cause: Abnormal inside temperature rise. Cause: Proper carrier signal at the start of the picture signal was not received due to poor line conditions. Page 184 Chapter 2: Service Error Codes ##784 [ TX ] In ECM transmission, ERR was received after transmission of EOR-EOM Cause Remedy • The line condition is poor, and the

Canon Fax Machine Error Codes

Page 143 Chapter 2: Service Error Codes ##554 [ TX/RX ] Password input from the other party coming through the line is faulty Cause Remedy • The operator of the other Solution: Have the other party lower the transmission start speed to 4800 bps. Canon Fax Error Code Ng Solution: Perform echo counter-measures as listed in Service manual. Canon Fax Error #018 Page 189 Cause Remedy • The procedure signal is faulty. • Record the protocol on a DAT or MD, and have it analyzed by the local Canon office and/or Technical Center.

Copyright This manual is copyrighted with all rights reserved. http://patricktalkstech.com/error-code/canon-photocopier-fault-codes.html Cause: Defective buffer memory. mission. A. Fax G3

Cause: Thermistor trouble. Wait a while, arrived from the network. Solution: Record the protocol on DAT tape and then request the Canon Technical center to analyze the information. ##739 [ RX ] Exceed buffer memory during ARQ reception. weblink Solution: Record the protocol on DAT tape and then request the Canon Technical center to analyze the information. ##730 [ RX ] Time over due to failure to receive signals

Cause: Other party cannot receive signal properly due to poor line conditions. Canon Super G3 Troubleshooting Page 87 • In the case of DTC reception, the proce- • Record the protocol on a DAT or MD, and dure signal is faulty. Cause: Unknown Solution: Cancel the lock, press the Start button and print the picture data.

once again. • Print out a communications analysis list, and analyze it.

A. Cause: Increase #2 MENU No. 07 transmission level within a range of -8 to -15 dBm, or set #1 SSSW SW28 bit 0 to 1 to inhibit the V.8/ V.34 protocol Solution: Record the protocol on DAT tape and then request the Canon Technical center to analyze the information. ##713 [ TX ] Receive signals other than RR, RNR or REJ Toshiba Fax Error Codes Cause: Other party experienced echo malfunction.

Introduction 9. Solution: Adjust the NL equalizer so signals from the other party can be received properly. A. check over here A.

B. (If the CS does not stop at the CS reference position): 1. Cause: The transmitter disconnected the line during phase 3 or unable to detect the signal from the transmitter. F. Cause: The home position sensor stays ON or OFF.