BAC replied 1 year, 9 months ago Bill Turtle said: ↑ Thanks for that. Published (2015-01-26 00:16:00) I had a loan Puma 230 that kept doing this two years ago while mine was in being fixed, the dealer had to keep coming out and recalibrating Repair as necessary or continue to test. ENG 2249 Injector Metering Rail 1 Fuel Pressure lower than commanded pressure. http://patricktalkstech.com/error-code/case-ih-puma-error-codes.html
Trans 2374 Master Clutch solenoid open circuit or short to ground. Cases begin in the same way. Does anyone know what this fault is? Use … Case puma.
Hold the shuttle button in, with the clutch pedal down, switch ignition on and leave for 10 seconds or so and you should hear it release BAC, Jan 25, 2015 ENG 237 External Speed Multi Unit Sync Command Input Data Incorrect. ENG 2292 Fuel Inlet Meter Device higher than expected.
Trans 2037 Bottom of Clutch pedal switch open circuit or bottom of clutch relay is stuck open Trans 2047 Clutch pedal bottom of clutch switch misadjusted. TRANS 74 The park brake ON with gear is engaged - no park brake request from calibration. ENG 758 Rear Bank injector is bad ENG 951 A power imbalance between the cylinders was detected by the controller hardware ENG 983 Unused A/D input channel out of range. Case Ih Transmission Fault Codes ENG 187 Sensor Supply 2 Voltage is too low.
Trans 2348 110 Clutch Mid Range solenoid open circuit or short to ground. Case Puma Error Code 12188 McMillan, III has 32 years of experience as a trial lawyer. Occ integrity check should return an exit code different than 0 in case of error PLEASE HELP Error EAC Error code 11 Game wont launch PLEASE HELP Error EAC Error code dd85 is online now PROCEDURE TO RELEASE trasmission park brake; it..tractor..Dave Customer Question I stert with error code12213, go through ASIST KM1407458 PROCEDURE TO RELEASE trasmission park brake; it doesn't do
ENG 2186 Supply Voltage to the accelerator pedal position sensor too low. Case Ih Code Reader Engine 3019 Boost Pressure Sensor -Signal Above Range Max. Place shuttle lever in park. Place the tractor on a flat level surface and block the tractor wheels to insure the tractor cannot move.
Mf 7480t3 hydraulic error code Mf 7480t3 hydraulic error code Case Puma 215 Case Puma 215 Related threads on other sites: 2013 Case Puma with error code 2013 Case Puma with NH 4008 Signal from Remote valve 2 Timer Pot 1 out of range NH 4009 Signal of Aux-stick (AUX3) out of range low NH 4010 Signal of Aux-stick (AUX3) out of Case Ih Puma Fault Codes Bill Turtle, Jan 25, 2015 #1 BAC Member Bill Turtle said: ↑ As per title, our Puma 185 is showing a problem with the electronic handbrake not releasing. Case Ih Error Codes Trans 2361 The creeper clutch solenoid is shorted to +12 Volts, current sensed while the driver is off Trans 2362 Master Clutch Solenoid is shorted to +12 Volts, current sensed while
ARM 1099 Aux remote valve LIMIT SET switch is failed ARM 1109 Hand Throttle IDLE VALIDATION switch is failed ARM 1119 RECORD/PLAY switch is failed ARM 1129 Invalid Configuration - Implement http://patricktalkstech.com/error-code/c5-error-code-lg.html case ih error codes - [Full Version] 5962 dl's @ 3435 KB/s case ih error codes - Full Download … Case IH Puma … monitored by a controller then there should If not successful continue. Ensure the EPL channel 2 is set to 'NO' and the instrument cluster IE channel 2 set to 'NO'. Case Puma 165 Problems
TMF 135 Aux 4th Lower Coil solenoid shorted to 12 volts. NH 10001 Upper lockout Solenoid error NH 10002 Raise Solenoid error NH 10003 Lower Solenoid error NH 10004 Front Axle Potentiometer above threshold NH 10005 Front Axle Potentiometer below threshold NH TRANS 74 The park brake ON with gear is engaged - no park brake request from calibration. http://patricktalkstech.com/error-code/case-error-code-14101.html Take shuttle lever out of park and place in neutral. ( press neutral button if it has it).
ENG 237 External Speed Multi Unit Sync Command Input Data Incorrect. Case Ih Tractor Error Codes ENG 755 Front Bank injector is bad. Test by back-probing the tractor harness connector with the key on: HAND BRAKE OFF (lever down): Pin Wire Color Voltage Function 1 177CA Bk 0v Ground circuit for EPL signal 2
The area Case rep says we over use it not sure I'm supposed to do chores with out getting in and out the cab a hundred times a morning. Hitch 1034 Slip Enable switch received from CAN data bus indicates failure condition. Note that passwords are case-sensitive. New Holland Error Codes Engine 3009 Coolant Temperature Sensor -(via CAN) No Signal Engine 3010 Air Intake Temperature Sensor -Signal Above Range Max.
How to fix this? Turn the key off and on and reinitialize. Error code 0xc0000225 followed by error code 0xc000014c... http://patricktalkstech.com/error-code/cal-spa-error-code-fl.html Thanks. _____ Message Cancel Changes: Quick Reply The following errors occurred with your submission: Okay: Message: Options.
With the key on 0 volts. ENG 2195 Auxiliary Equipment Sensor Input # 3 - Engine Protection Critical - Special Instructions. TMF 137 Aux 4th Raise Coil solenoid shorted to 12 volts. Trans 2071 Forward switch input from the FNRP Pod is shorted to ground or is open circuit.
NH 3125 Hand Throttle potentiometer 2 Low error. NH 15006 Split valve LVDT open circuit. Engine 3273 Fuel Low Pressure Sensor -Signal Below Range Min. ENG 2311 Electronic Fuel Injection Control Valve open or closed Circuit.