Recommended Action: See the recommended action for error code 144. Check the clutch operation (Life test command)3. The CDM NOA cannot create the profile under the technology object. Test the dispenser by completing several test dispenses. 4. this content
Trying to restore a connection that refers to a nonexisting (removed) chassis. If error persists, replace the dispenser mechanism. In the case of restorePVC, this error message may be the result of an internal error. Results: No money is dispensed, screen and receipt display system unavailable.
Clean the sensors (CS1~CS15) in cash dispenser 4006000Something is detected in C331A, CS31B sensor before dispense operation 4006100Something is detected in C331A, CS31B sensor before dispense operation 4006200Bills is staying in CDM_311Unable to delete the subscriber object for ingress port. Replace the modem module.
If the error code is reported again, replace the CMC module. CDM_114Unable to get ingress VPI value from work order. This error code will cause the cash dispenser to go "Out of Service". Sbi Atm Response Code 070 Means Make sure there are no chassis which are not DSLAMs in the subtend view.
Remove dust in CS1AB, CS15AB, CS31AB, CS41AB Sensor 4. Atm Response Code 072 Make sure that there is no foreign material in the card slot. Reboot ATM 2. Check the log files.
Rearrange notes in cassette 3. Wincor Nixdorf Atm Error Codes If the dbo.EncryptionKeyPairs table is empty in the CognosDM Database, recreate the keys manually: a. Exchange a sensor after abnormal operating the CS31B. 4009DTrying to dispense bills from 3rd cassette but the 3rd cassette doesn't installed. 4009D3 Cassette not available during dispense reserved operation1. Remove any documents from the tote transport.
Otherwise, the possible causes of the problem may be a defective paper low sensor, or a defective printer control PCB. Remove the remaining notes or foreign objects on the gate 2. Sbi Atm Error Codes Reboot ATM 2. Atm Error Code 3-da001 CDM_521Unable to create the profile object under parent NI1SubscriberProfiles:/ATMQoS.
CDM_532Unable to create the profile parent profileContainment:
/CAPTech for adding profile objects. news The CDM NOA cannot create the profile under the technology object. Profile does not exist. Buy the Full Version Wincore Error Codes.pdf by nag33pp2.5K viewsEmbedDownloadDescriptionatm error codesatm error codesInterests: TopicsRead on Scribd mobile: iPhone, iPad and Android.Copyright: Attribution Non-Commercial (BY-NC)List price: $0.00Download as PDF, TXT or Ncr Atm Error Codes
If the error clears, put the cash dispenser in service. 3. Reinstall software 3. Unable to communicate with the node due to invalid passwords. have a peek at these guys Check CS7 Sensor Cable4.
Open the access panels on the note transport and remove any documents that may be in the transport path. Sbi Atm Response Code List Pdf Remove each note feeder module from the dispensing mechanism and clean their associated empty, pressure and exit sensors with clean compressed air. Check notesÕ status in 2 Cassette 2.
If the cable is undamaged and DC voltages are correct, the main board, electronic journal, or dispenser may be defective. Check the status of setting paper 2. CDM_307Auto allocation not supported for NI-1 systems. Wincor Atm Error Codes Check get_object_for_line
Check foreign objects at the position of the CS5 Sensor Guide 4. Error Code: 205 Description: SPED keypad reported tamper condition. Reset the error. http://patricktalkstech.com/error-code/cch-error-codes.html Clear the error.
Error Code: 305(35h) Description: Diverter Failure. Error Code: 160 Description: Electronic journal set featured failed. Recommended Action: An attempt to feed or dispense documents has been made when there is a note in the note transport throat. Make sure all connectors attached to the CMC are seated in their receptacles.
Recommended Action: Error code valid only for units with SPED keypad device installed. Invalid policy. Otherwise, replace the dispenser. Set cassette #1 correctly 2.
Results: No money is dispensed, screen and receipt display system unavailable. Please try the request again. Turn the AC power OFF for a few seconds and then back ON to power cycle and reset the cash dispenser. It will also be stored as part of the transaction data in the electronic journal.
Make sure the line ID is set correctly for the port. Clean CS1A and CS1B 40028CS13 sensor detects note in delivery path before/after CDU dispenses1. Remove note from the CDU delivery path. 2. Check notes dispensed and rejected 2.
CDM_103 Missing Connection Identifier value in work order. Recommended Action: Enter management functions and make sure that the cassettes are programmed and placed in service. Wait the time until the temperature of head adequately slow down and try to initialize 20103Receipt paper jam1. Loss of communication with the node.
Check specifications of 3 Cassette FM Board Dip Switch (#2, #4, #6 On)4. Possible reasons: The given VPI/VCI on the ingress or egress side are not available.